Evinrude 6Hp 2 stroke Problems
| Engine Model: Evinrude 6 Hp 2 stroke |
| Engine Type: 2-stroke single-cylinder gasoline outboard engine |
| Total Displacement: 7.5 cu.in (123 cc) |
| Rated Engine Power: 6 Hp (4.4 kW) at 6000 rpm |
| Fuel System: Carburetor |
____________________________________________________________________________________
| Engine difficult to start or won't start |
No gasoline in tank - Fill gasoline up.
Wrong fuel grade - Change fuel.
Water or air in fuel system - Remove air or water from system.
Spark plug wire is loose or disconnected - Inspect spark plug wiring connection, change or repair.
Faulty spark plug - Install new spark plug.
Fuel filter is clogged - Replace or clean fuel filter.
Carburetor is clogged - Clean the carburetor.
Clogged fuel lines - Clean fuel system lines.
Closed or restricted fuel tank air vent - Open or service air vent.
Low fuel pump pressure - Replace or rebuild fuel pump.
Worn or faulty reed valve - Replace reed valve as required.
| Engine starts and stalls suddenly |
Spark plug is defective - Replace spark plug.
Faulty or dirty carburetor - Clean or change carburetor.
Ignition coil is defective - Change ignition coil as required.
Fuel tank air vent clogged or closed - Fuel tank air vent need to be opened or cleaned.
Low fuel pump pressure - Repair or change fuel pump.
Ignition failure - Inspect ignition system and change faulty parts.
Clogged or damaged fuel pump - Service or change fuel pump.
Carburetor problems - Carburetor diagnostics required.
Dirty fuel lines - Fuel lines must be clean.
Closed or clogged fuel tank air vent - Fuel tank air vent need to be opened or cleaned.
Plugged fuel filter - Change fuel filter.
Gaskets are damaged - Replace gaskets.
Engine overloaded - Load reducing is recommended.
Too lean carburetor mixture - Make the correct settings.
Wrong ignition timing - Adjust ignition timing correctly.
Thermostat is faulty - Change thermostat.
Water pump malfunction - Water pump need to be replaced.
Incorrect propeller selection - Replace propeller.
Damaged or bent propeller - Replace propeller.
Outboard engine is mounted too high or too low - Mount the motor as required.
Low octane fuel - Use correct fuel.
Engine is under excessive load - Load reducing required.
Too low idle RPM - Correct the settings.
Fuel pump is faulty or clogged - Check fuel pump and replace if necessary.
Crankshaft or main bearings are worn out - Crankshaft or bearings need to be replaced.
Cylinder bore or piston rings are damaged - Replace faulty components.
Carburetor is incorrectly adjusted or clogged - Clean or properly adjust carburetor.
Clogged or defective fuel pump - Test fuel pump and change if necessary.
Ignition system problems - Test ignition and replace failed parts.
Damaged gaskets - Replace gaskets.
Powerhead parts are worn out - Replace defective components.
Propeller pitch or diameter incorrect - Install correct propeller.
Damaged or bent propeller - Replace propeller.
Incorrect outboard motor mounting height - Check the outboard engine mounting height.
Improper trim angle - Make the correct trim angle adjustment.
Carburetor main jet is improperly adjusted - Adjust it correctly.
Faulty or loose spark plug - Spark plug need to be replaced or tightened.
Worn sleeve, rings, or piston - Replace defective parts.
| Engine vibrates excessively |
Damaged or bent propeller - Replace propeller.
Propeller shaft malfunction - Have propeller shaft replaced.
Weeds clogs the propeller - Remove and clean propeller.
Engine mounting bolt is not tightened - Tighten bolt.
Loose or faulty steering pivot Tighten or replace.
____________________________________________________________________________________
| Outboard Engines Technical Specifications |
| Small Engines Technical Specifications |
| Car Engines Technical Specifications |
| Industrial Engines Technical Specifications |
