Deutz TCD 2013 L06 2V Troubleshooting
| Engine Model: Deutz TCD 2013 L06 2V |
| Engine Type: 4-stroke in-line 6-cylinder turbocharged water-cooled diesel |
| Total Displacement: 439.4 cu.in (7.14 L) |
| Rated Engine Power: 268 hp (200 kW) at 2300 rpm |
| Fuel System Type: Common Rail Direct Injection |
____________________________________________________________________________________
| Engine hard to start or won't start |
Clogged fuel filter - Clean or replace the filter.
There is air in the fuel system - Bleed the system.
Fuel injection nozzles are clogged or faulty - Replace injection nozzles.
Fuel injection pump is not working correctly - Rebuild or change fuel pump.
Valve timing is improper - Use correct valve timing adjustment.
Plugged fuel pipes - Clean or replace fuel pipes.
Injection timing is wrong - Adjust injection timing as required.
Cylinder or piston rings are worn - Change defective parts.
| Engine starts and stops suddenly |
Fuel filter plugged - Change the filter element.
Fuel injection pump is faulty - Rebuild or install a new injection pump.
Air filter is dirty - Install new air filter element.
Nozzle opening pressure is improper - Adjust according to specifications.
| Engine shuts off while running |
Incorrect adjustment of fuel injection pump timing - Adjust the pump as required.
Fuel filter element clogging - Service or replace the filter.
Engine has not warmed up to the recommended temperature - Warm up the engine.
Stuck or burnt injection nozzle - Repair or replace injection nozzles.
Wrong adjustment of low idle speed - Adjust low idling as recommended.
Excessive valve clearance - Check and adjust.
Damaged fuel injection pump - Change or repair the pump.
| Engine power is insufficient |
Fuel injection nozzles are faulty or clogged - Check injection nozzles and replace if required.
Dirt in the fuel hoses or lines - Clean fuel lines and hoses.
Air filter element clogged - Clean or replace element.
Cylinder-head gasket is broken - Replace cylinder head gasket.
Injection timing is incorrect - Adjust as recommended.
Fuel injection pump malfunctioning - Repair or replace injection pump.
One of moving engine parts has broken - Change or repair damaged parts.
Radiator core is dirty or radiator cap is damaged - Install new cap or clean radiator.
Lack of engine coolant - Fill radiator to proper level and check components for faults.
Fan belt is loose or defective - Install new fan belt.
Engine oil insufficient - Need to add engine oil.
Cylinder head gasket defective - Install new cylinder head gasket.
Injection timing is wrong - Adjust injection timing as required.
Low oil level - Add oil to the engine crankcase.
Oil pump is defective - Inspect and change as required.
Oil filter element is dirty - Replace or clean engine oil filter element.
Relief valve is stuck or broken - Relief valve need to be replaced or cleaned.
Excessive crankshaft bearing clearance - Check and change or repair defective parts.
Excessive crankpin bearing clearance - Test and repair or replace worn parts.
| Engine using too much oil |
Oil leakage: Seals or gaskets are wearing excessively - New components need to be installed.
Oil viscosity is wrong - Use proper viscosity oil.
Damaged or seized piston rings - Replace piston rings.
Worn valve guides and valve stems - Valves need to be changed.
Scuffed cylinder liners or pistons - Inspect pistons and liners, replace as required.
Engine has not warmed up to the recommended temperature - Normalize the temperature by warming up the engine.
Not enough engine oil - Fill up the engine oil.
Wrong setting of fuel injection pump timing - Set the fuel pump timing correctly.
Worn or scored pistons - Have pistons replaced.
Connecting rod is misaligned or worn - Need to change or align the connecting rod.
Battery capacity is low - Battery is drained, recharge it.
Battery is not holding charge - Service charging system or replace battery.
Battery cables are disconnected or terminals are faulty - Connect cables correctly or replace terminals.
Battery is discharged or worn - Need to charge or replace the battery.
Disconnected or incorrectly connected wires - Inspect battery wires and connect correctly.
Low battery power - Recharge the battery.
Starter motor is defective - Starter should be changed.
____________________________________________________________________________________
| Industrial Engines Technical Specifications |
| Car Engines Technical Specifications |
| Small Engines Technical Specifications |
| Outboard Engines Technical Specifications |
